I have tips for driving corners

Due to terrain, traffic conditions and driving resistance, vehicles often require deceleration when turning. At this time, the driver must select the appropriate gear according to the needs of the power and the speed of the turn, and safely pass through the curve. The following seven different road turning techniques can be used by bikers, especially those who just got a driver's license.

1. Turning of streets or access gates The driver should pay special attention to debris accumulating along the roadside, decelerate and whistle within 50 to 100 meters, and use a turn signal or hand gesture to indicate the direction of travel. At night, use a small light to achieve "a slow, two look, three pass," pay close attention to the inside of the car turn, beware of roadside parallel and unknown direction of the car in the direction of pedestrians, bicycles, motorcycles scramble; at the same time, also Pay attention to the collision between the outer side of the front wheel and the inner side of the rear wheel and the rear of the vehicle, the container and the obstacle, and rub it together.

2. Turning drivers on narrow roads should honk the horns 50 to 100 meters before the start of the turn, depending on the road condition, and slow down. When the car is inconvenient to see a bend, the car should be quickly driven to the right side of the road so as not to interfere with the normal operation of other vehicles.

3, the turning of the intersection When the left turn, the driver should send a signal in advance, relying on the center of the road as far as possible when turning, to provide convenience for the rear car and right turn of the car; when turning right, the same must first send a turn signal, turn to Slowly, and at the same time pay attention to the effect of the internal wheel deviation when steering, and prevent the right rear wheel from driving out of the road to scratch pedestrians and obstacles.

4. The driver of heavy fog and windy days turning in this kind of weather must be aware of how to turn on the headlights and fog lights as soon as possible and diligently press the horn to cause the attention of pedestrians and other vehicles to slowly advance. And ready to stop braking at any time.

5. The driver of a turn on rain, mud, and mud shall use the role of the engine traction resistance in advance to reduce the speed of the vehicle and move forward slowly, and try hard to avoid violent direction and sudden braking. When going uphill, in the event that other vehicles cause a blockage in the corner due to skidding on the slope, the vehicle should be stopped to the right in advance, and should be forwarded after the vehicle passes through it; when it comes to turning downhill, it should be prevented The car was slippery and crashed.

6. When a turn at a steep slope approaches a curve, it must decelerate and whistle. When turning on a steep slope, it should be pre-shifted into a low gear in order to obtain enough power for climbing and avoid shifting during cornering to prevent accidents. The steering timing should be properly selected, and one-time cornering should be implemented so as to avoid turning the vehicle once and then turning once after turning is not possible due to improper steering. This increases the danger.

7. Turning on Lushan Insurance Road Because of complex road terrain, short sight distances and unclear frontal conditions, speed and diligent horn should be controlled. At any time, choose the location where the roadbed is solid and the road is relatively wide. If the front side of the curve finds that the other party has arrived and the car has not yet met, it should select an appropriate location and take the initiative to courteous confiscation so that the other party can easily pass through the car. In short, the vehicle must first control the speed of the vehicle before turning, and make preparations for parking at any time. Try to avoid the use of emergency braking and detours. When turning, steering the steering wheel must match the speed of the vehicle. Turn it back in time and back in time. The angle of steering must be determined by the facts and avoid accidents.

Aluminum Decoration Profile For Construction

1.Application:Decoration Profile For Construction
2.Dimension: Customized dimension, OEM & ODM
3.Material: A6063, A6061, A3003 and other series alu alloy
4.Suface treatment: Anodizing, polishing, turning ,power coating, mill finish etc
5.Equipment: CNC ,extruding machine, cold drawn machine, heating oven, straightening machine, cutting machine

OD

OD Tolerance

ID

Tolerance

Roundness

Straightness

Circular

run-out

φ16-20

±0.02

±0.02

0.01↓

0.015↓

0.05↓

φ20-30

±0.02

±0.02

0.01↓

0.015↓

0.05↓

φ30-50

±0.05

±0.05

0.02↓

0.020↓

0.08↓

φ50-80

±0.15

±0.10

0.05↓

0.025↓

0.10↓


6. STANDARD PACKING:Wooden case/carton

7. Trade Terms
1. Payment: 30% T/T in advance, 70% balance pay before delivery. L/C at sight.
2. Delivery time: 20 days after deposit receiverd. If opening mould, plus 7-10 days.
3. Trade Term can be chosen depending on your requirements.
4. FOB Port: Shanghai
Contact Us
If you want more info.about the aluminum tubes/profiles, please feel free to contact us.
1. Attn: Karina Gu
2. Mobile: +86-18961469527
3. Tel: +86-519-88761254

Aluminum Decoration Profile For Construction,Aluminum Decoration Profile,Aluminum Construction Profile,Aluminum Building Profile

Changzhou YiFei Machinery Co., Ltd. , https://www.yifeialu.com