The medical waste transfer vehicle is classified as a van model, which is a vehicle that specifically consigns waste generated in hospitals. For the use of medical waste transfer vehicles, China has strict rules and regulations and must be implemented in accordance with the rules and regulations when it is used. Before using, please first understand what it needs to pay attention to. First, the medical waste transfer vehicle can only be used for the collection and transportation of medical waste and must not be used for other purposes. Second, when the vehicle is in motion, it is necessary to lock the carriage to ensure safety. It is not allowed to lose or leave and pack medical waste on the way. Third, medical waste transfer vehicles must be equipped with special boxes to prevent the spread of pollution. Special boxes must have: (a) Disinfection equipment and disinfectants; (b) Collection tools and bags; (c) Personnel hygiene protection supplies, etc. Fourth, special emergency vehicles must be kept in good condition at any time, fully equipped. 5. In order to ensure that the medical waste turnover box does not tip over in the event of an emergency start, stop, or accident of the vehicle during non-full-load transportation, the consignee should fix the cargo. 6. After each transfer of the medical waste transfer vehicle is completed, the vehicle body and the compartment must be sterilized immediately at the designated site. The disinfectant should be sealed for at least 30 minutes after spraying. 7. The medical waste transfer vehicle must be cleaned and disinfected every day in the body and compartment. It is forbidden to clean the medical waste transfer vehicle off site. VIII. Medical waste transfer vehicles shall not be allowed to board other unrelated personnel, and may not be loaded or mixed with other goods. Nine, medical waste transfer vehicles to implement a car one card system, do a good job vehicle maintenance, fault repair, driving records and other relevant information for the establishment of card work, and safekeeping. X. Before the medical waste transfer vehicle leaves the vehicle, the driver must check the condition of the vehicle and other facilities to ensure that the vehicle is in good condition. The medical waste transfer vehicle is a special type of special vehicle. It can effectively avoid environmental pollution while transporting waste. Automatic Common Mode Inductance Winding Machine Common mode inductor winding direction difference? Automatic Common Mode Inductance Winding Machinery, Common Mode Winding Machine, Common Mode Inductance Winding Machine SUZHOU DEGU MACHINERY CO.,LTD , https://www.deguwindingmachine.com
1: Is the winding direction of common mode inductor opposite? This is bullshit. The winding direction of common mode inductors is the same, and the magnetic fluxes of common mode current parameters cancel each other. Therefore, magnetic materials with high permeability can be used to achieve small volume and large inductance without saturation. The interference between the two power lines to the ground is called common mode interference. How does this common mode inductor work when there is no ground wire on my power supply? The so-called common mode current is the current flowing into or out of the LN line at the same time. When testing the conduction, use the artificial LISN network. The relevant knowledge can remind you not to forget the parasitic capacitance of PE.
2: Common mode winding inductance is to wind two windings with the same phase and same number of turns on the same magnetic core. The reverse magnetic field generated by the current will cancel each other, so it will not cause saturation. As for the winding direction you see, I don't know if it is the winding direction. If it is wound on the same side, then the two winding directions are opposite, one clockwise and the other counterclockwise, If it's a different side winding, it's clockwise. So this problem is a little different. It depends on how you define it. No matter how you wind, it's OK to ensure the same phase and number of turns. For the second question, refer to the answer from the upstairs. Generally, the test conduction needs to be connected to the LISN, and output to the load, the load and the product to be tested through the LISN. There is GND access signal on the LISN.
What is the difference between wound inductor and laminated inductor?
Wound inductor is the product of traditional wound inductor miniaturization. Laminated inductor is made by multi-layer printing technology and laminated production process, and its volume is smaller than wound chip inductor.
Winding inductor: it is characterized by a wide range of inductors (MH ~ H), high accuracy of inductor, small loss (i.e. large Q value), large allowable current, strong inheritance, simple manufacturing process and low cost; The disadvantage is that it is limited in further miniaturization. The ceramic core wound chip inductor can maintain a stable inductance and a fairly high Q value at such a high frequency, so it occupies a place in the high frequency circuit.